Custom ASIC Mining Controllers

Custom ASIC Controllers for your Mining Gear

Starting at just $50 USD – Available Now at SantaCruzASICs.com

Setup your miners with a simple, affordable, efficient controller – no need to have a PC setup at all.  Our controllers run as little just 5 watts of power – your power-hungry PC can be retired as a miner controller.  The small size of the controllers allows you to place them nearly anywhere – get creative!

A robot USB2 hub, filled with 3 ASICMINER Block Erupter USBs for a total of over 1GH/s
A Robot USB2 hub, filled with 4 ASICMINER Block Erupter USBs for a total of over 1.2GH/s

Our controllers can be used to make modern art that actually mines – like this little robot USB hub miner – 1.2GH/s of ASICMiner AMU sticks in a cute robot USB hub:

scrypt ASIC and/or SHA256 (Bitcoin) ASIC

The controllers can be custom-configured to drive a whole range of ASIC gear – from simple USB sticks like the original ASICMiner Block Erputer [sic], Bitmain U1, U2 & U3s, Bitfury RedFury et al, Cryptorig Hitchhikers, and more – to higher-end faster gear, such as Rockminers, Spondoolies, Butterfly Labs Monarchs, BitCranes, etc. Basically, anything that can be run by open source miner software BFGMiner or cgminer: both scrypt and SHA2 miners are supported.  We’ve successfully run Gridseeds scrypt gear, as well as Bitmain & ASICMiner USB SHA2 stick miners, with the same controller, at the same time – tho for maximum performance, we advise 1 controller for each device type.

Contact us today if you have any questions, we’ve been mining crypto for over 5 years, and have crafted a bunch of these RasPi, Cubieboard or Beaglebone based controllers with great success, or complete the form below to begin the process of getting your own custom ASIC controller – simple plug & play performance, set it and forget it, no need to manage computers / PCs and drivers, no hassles!

Priced from just $50 – includes Cubieboard, Case, and Custom configured mining operating system, upgrade options available.

USB Stick Miner Information:

As ASIC chips are known to be rather power-hungry, and faster and faster chips are being used in USB form factor stick miners, powering the sticks in a USB hub has always been a challenge.  Some sticks can draw far in excess of the spec of USB power – thus power management becomes key.  The fine folks at eyeboot.com have a serious USB hub which delivers a full 10 amps to the hub, or 1A per device – great for running USB ASIC Bitcoin miners.

RasPi2 ASIC controller, with PyGlow & Wifi Addons
RasPi2 ASIC Miner controller, with PyGlow & Wifi Addons
nanos-in-usb2hub
4 Avalon Nano USB sticks running on a Santa Cruz ASIC controller
cgminer console display
cgminer console display

Custom ASIC Miner Controllers

Santa Cruz Custom ASIC Controllers

Setup your miners with a simple, affordable, efficient controller – no need to have a PC setup at all.  Our controllers run as little just 5 watts of power – your power-hungry PC can be retired.  The small size of the controllers allows you to place them nearly anywhere.

The controllers can be custom-configured to drive a whole range of ASIC gear – from simple USB sticks like the original ASICMiner Block Erputer [sic], Bitmain U1 & U2s, Bitfury RedFury, Cryptorig Hitchhikers, and more – to higher-end faster gear, such as Rockminers, Spondoolies, Butterfly Labs Monarchs, BitCranes, etc. Basically, anything that can be run by BFGMiner or cgminer.

Contact us today if you have any questions, we’ve been mining for over 5 years, and have crafted a bunch of these RasPi or Cubieboard based controllers with great success.

Starting at just $59.95 – for a customized RasPi2-based ASIC controller, complete with fully configured operating system pre-installed and tweaked for your environment. Provide your pool information for a fully plug & play setup – get mining in minutes!

To order a Cubieboard2 Customized ASIC Controller, click the order button below: